Electrical & low voltage
Outlet & switch locations — Match the drawings; every bed, sofa, desk and island position has the outlets it needs.
GFCI protection — Kitchen counters, bathrooms, laundry and outdoor outlets are GFCI-protected and trip when tested.
AFCI protection — New habitable-room circuits have AFCI protection as required by local code.
Dedicated circuits — Range, oven, dryer and AC have dedicated circuits; every breaker in the panel is labeled.
Low-voltage points — Data, TV, intercom and camera runs are in place, with a spot for the router.
Rough-in inspection — Work by a licensed electrician; on permitted jobs, close walls only after the electrical inspection.
Plumbing & waterproofing
Supply pressure test — Hot and cold lines hold pressure for the full test with no drops or weeping joints.
Drain slope — Drains are correctly sloped with intact traps; no backflow or odor after running water.
Shower waterproofing height — Membrane runs high enough on shower walls (commonly above the shower head) with reinforced corners.
Flood test — Floor and shower pan hold water for 24–48 hours with no leaks below or in the walls.
Floor drain — Drain sits at the low point and floors slope to it; no standing water after a shower.
Access panels — Shut-offs, manifolds and tub motors have access panels and working valves.
Walls & ceilings
Drywall seams — Seams are flat and crack-free; check flatness with a long straightedge.
Wet-area substrate — Bathrooms and kitchens use moisture-resistant board or cement board, not standard drywall.
Paint finish — Raking light shows even color, no runs, brush marks, holidays or pinholes.
Corners — Inside and outside corners are straight with no exposed corner bead.
Light layout — Recessed and track lights are centered and aligned with clean cut-outs.
Floors & tile
Hollow tiles — Tap-test with a small hammer; large or corner voids must be redone.
Grout lines & lippage — Joints are even and straight; edge height difference between tiles stays within tolerance.
Wood floor expansion gap — Perimeter gap is left and covered by baseboard; no squeaks or cupping when walked.
Transitions — Thresholds between materials are smooth and door clearances are correct.
Grout & caulk — Grout is full; wet corners and counter joints have mildew-resistant caulk.
Cabinetry & millwork
Door gaps — Even reveals, smooth swing, soft-close hinges working.
Drawers — Drawers glide smoothly and stay level when loaded.
Edge banding & emissions — Edges are fully bonded; panels meet CARB Phase 2 / TSCA Title VI with documentation.
Countertops — Tight, flush seams; sink and cooktop cut-outs sealed; backsplash caulked.
Anti-tip anchoring — Tall units and bookcases are anchored to the wall — essential with children.
Doors, windows & hardware
Interior doors — Swing freely with even gaps; latches and stops installed; no floor rub.
Windows — Operate smoothly, seals intact, no noticeable drafts when closed.
Hardware match — Pulls, hinges and faucets match the approved selections with no scratches.
Kitchen, bath & equipment
Faucets & fixtures — Hot on the left, cold on the right, no drips; toilets flush well and sit firm.
Shower glass — Tempered safety glass is marked and the door seals when closed.
Ventilation — Bath fans vent outside; range hood airflow and ducting follow building rules.
Appliances & gas — Appliances installed per manual; gas connections by a licensed plumber and leak-tested.
HVAC — Every room heats and cools; thermostats work; condensate drains properly.
Paperwork & close-out
Smoke & CO alarms — Smoke and carbon-monoxide alarms installed and tested as NYC requires.
Permit sign-off — Permitted work has DOB sign-off; building close-out documents are submitted.
Punch list — Every punch-list item is complete before final payment.
Documentation — Warranties, manuals, material and color specs and as-built drawings are filed.
Attic stock — Spare tile, flooring and paint are labeled by room and batch for future repairs.
Payment records — Keep payment records and request lien waivers where appropriate.